Sometimes customers ask, when using packing seals, it is required that water leak out at the sealing point to cool the shaft, which would cause the pump installation site to be unclean. Then why is there still a requirement to use packing as the pump shaft seal?Despite the risk of leakage, packing seals are still widely used in some pump types, mainly for the following reasons: ;Youdaoplaceholder0 Cost and maintenance advantages ; : The packing seal has a simple structure, low manufa

Often, customers of ATACH Pump Industry order chemical centrifugal pumps without motors and bare shaft parts. Therefore, after receiving the pumps, the motors held by the customers themselves need to be coupled and connected to the ATACH bare shaft pumps. Now, we will explain the connection requirements and precautions as follows:When connecting the motor of a split-type chemical pump, a ; dial indicator is used to ensure the ; shaft alignment accuracy of the ; coupling, avoidi

Some new customers, when consulting the sales department of ATACH about the selection of mechanical seals for pumps, often say that they should provide us with the best quality mechanical seals because they are not very familiar with mechanical seals. In fact, this statement is not accurate. Each type of mechanical seal made of different materials has its suitable working conditions. Even the very cheap nitrile rubber performs well when used in oily media. The technical department of ATACH Pump

Some time ago, an old customer from the UK asked us. They were clear about the parameter requirements of the water pump, but they were confused about whether to choose the vertical or horizontal structure of the water pump. Which installation structure is more suitable? Now, Aitek Pump Industry will make an analysis and explanation:Vertical water pumps and horizontal water pumps each have their own advantages and disadvantages in terms of structure, installation, performance and maintenance. Whe

ATACH Pump Industry supports the processing and production of shafts made of special materials, with high cost performance.The material selection for the main shaft of a chemical centrifugal pump should be determined based on the characteristics of the medium (such as corrosiveness, temperature, and pressure) and the requirements of the working conditions. Common materials include carbon steel, ; stainless steel, ; alloy steel, etc., as follows:Carbon steelHigh-quality carbon structu

This is a significant misunderstanding.Many customers think that if they need a head of 20 meters, then a pump with a head of 50 meters should be more than sufficient.However, they are unaware that this will directly cause motor overload and, in severe cases, burn out the motor.The analysis is as follows:When a ;; centrifugal pump is used below its designed head, the resistance at the outlet decreases, resulting in a significant increase in flow rate. The motor load exceeds the rated

Many of ATACH's customers may ask why stainless steel 304 is often not recommended for seawater or media with high salt (chloride ions) content, but duplex steel 2205/2507 or bronze is more recommended?Now we elaborate on this issue as follows:Bronze impellers are widely used in seawater or brine media, mainly due to their excellent corrosion resistance, wear resistance and mechanical properties. The following are the specific reasons:Corrosion resistanceBronze (a copper-tin alloy) can form

Many customers receive pumps delivered by ATACH, especially those that require self-priming and have a height difference for water intake.They do not understand the emphasis made by ATACH technicians that a bottom valve must be installed at the water intake end of the water inlet pipe.Now we make an analysis:The core function of the ; bottom valve for the safe operation of the water pump is to prevent water backflow, keep the pipeline full of water, avoid cavitation and impurities from ent

Note: If there are any special requirements or usage conditions, please contact the ATACH sales representative. The sales representative will select the model specifically to avoid failure to meet the usage conditions or abnormal damage to the purchased pump products.The maximum medium temperature of the ATACH brand stainless steel corrosion-resistant submersible pump usually does not exceed 100℃, which depends on the material and design of the pump body.The following is the key information:Mat

Based on years of analysis of customer usage by ATACH Industrial Pump Factory and research on on-site feedback from customers, the following analysis and elaboration are mainly made regarding the situation of main shaft breakage in chemical centrifugal pumps:The breakage of the main shaft of a chemical centrifugal pump is usually caused by fatigue failure, design flaws, abnormal operating conditions or installation issues. The following are the specific reasons and solutions:Fatigue failureThe m

To prevent dry pumping of centrifugal pumps equipped with mechanical seals, efforts should be made from three aspects: seal management, equipment maintenance and operating conditions ;.The core is to avoid air entering the pump body and dry friction on the sealing surface.Sealed managementStrictly inspect the dynamic and static seals: During maintenance, it is necessary to ensure that the seals are not damaged or aged to prevent air from leaking into the medium through the pipeline or pump

The transportation of organic solvents and adhesives requires the selection of pump type ; based on specific properties. The following are common schemes:Centrifugal pumpIt is suitable for low-viscosity organic solvents without solid particles (such as gasoline and benzene), with a simple structure and stable flow rate. ;Positive displacement pumpGear pump: Suitable for medium-viscosity adhesives, such as polyurethane glue and silicone. ;Screw pump: It can convey high-viscosity