The main differences between stamping pump parts and casting pump parts are reflected in three aspects: ; processing technology, structural characteristics and applicable scenarios ;.Differences in processing techniquesstamping ; : By applying pressure to metal sheets through molds to form them, it features high production efficiency and a material utilization rate of up to 70%-80%, making it suitable for mass production of simple or moderately complex parts. ;casting 

The standard centrifugal pumps of the ATACH brand do not overload under all working conditions, which is mainly closely related to their product design, selection strategy and operation control technology:Selection strategyATACH uses a dynamic load assessment model for selection and continuously monitors the working conditions for 72 hours through a power analyzer to ensure that the rated power of the motor precisely matches the actual load demand. For instance, when dealing with high-viscosity

Chemical pumps must be equipped with explosion-proof motors in places where flammable and explosive substances exist. The specific scenarios are as follows:Explosion-proof demand scenarios1.flammable gas/vapor environment ;In petrochemical production, common flammable gases (such as natural gas, hydrogen, etc.) or vapors (such as gasoline vapor) may reach the explosive limit concentration when mixed with air. At this time, explosion-proof motors need to be used. ;2.combustible dust/f

There are significant differences in composition, application and characteristics between the grease and engine oil used in the suspension of centrifugal pumpsComponent differencesgrease is mainly composed of base oil and extreme pressure anti-wear additives, emphasizing anti-wear and rust prevention properties. It is suitable for low-speed and heavy-load rolling bearing. ;engine oil ; contains components such as detergents and dispersants, antioxidants, etc. It is mainly used for in

316 stainless steel can withstand seawater environments, but the appropriate model should be selected based on specific working conditions and protective measures should be taken. The following are the key points:Applicability analysis316 stainless steel (especially 316L) is widely used in medium and low load scenarios such as seawater desalination and ship deck motors due to its lower carbon content (≤0.03%) and superior corrosion resistance compared to ordinary 304 stainless steel. However, h

Plunger pumps and multistage centrifugal pumps each have their own advantages and disadvantages and are suitable for different scenarios:Advantages of plunger pumpsHigh-pressure capacity ; : The working pressure can reach 30-70 mpa, suitable for high-pressure scenarios such as hydraulic systems and oilfield water injection. ;High efficiency ; : The volumetric efficiency can reach over 90%, and the energy conversion efficiency is superior to that of centrifugal pumps. ;Adj

The selection of the mechanical seal (mechanical seal) configuration for water pumps should be comprehensively considered based on the characteristics of the pumped medium, working conditions and equipment parameters. The following are the key points for selection:Medium characteristicsClean water ; (if no abrasive additives) : It is recommended to combine ceramic/carbon materials (ceramic stationary surface + carbon rotating surface) with nitrile rubber sleeves, which is cost-effective an

Direct-coupled centrifugal pumps and centrifugal pumps with couplings each have their advantages and disadvantages. The specific choice should be based on the application scenario:Characteristics of direct-coupled centrifugal pumps• ; advantages ; : Compact structure, small floor space, no need to adjust the concentricity of the shaft system during installation, and smooth operation. ;• ; disadvantage ; : When the pump shaft is worn, the entire motor rot

The reasons why Dongguan ATACH Pump Co., Ltd. has become stronger and larger in the field of industrial pumps and chemical pumps mainly include the following aspects:The products have a wide coverageThe company offers a wide range of pump products, including stainless steel anti-corrosion pumps, fluorine-lined chemical pumps, pipeline centrifugal pumps, and cantilever centrifugal pumps, covering scenarios such as dyeing and finishing, chemical engineering, food, and environmental protection. It

When a semi-open impeller centrifugal pump is used to convey liquids containing solid particles, fibers or viscosity, a semi-open impeller should be adopted. ;Applicable scenarios1. liquids containing solid particles or fibers ; : The semi-open impeller has no front cover plate and the flow channel is semi-closed, which not only reduces the risk of clogging but also maintains high efficiency. It is suitable for conveying liquids with a large amount of impurities such as sand and fibe

DONGGUAN WATER PUMP FACTORY SUPPLIES THATThe selection of centrifugal pumps should be based on specific process requirements and industry standards. The following are the key points:Standard SpecificationGive priority to referring to American national standards such as ANSI/HI 9.6.1, ANSI/HI 9.6.3, and ANSI/HI 9.6.4. These standards provide general guidelines for net positive suction head (NPSH), preferred working area (POR), and allowable vibration values. Industries such as petrochemicals and

IHF steel lined fluorine plastic chemical pump is derived from the traditional IH stainless steel chemical pump, with the increasingly stringent requirements for environmental protection and chemical pumps, the traditional IH chemical pump because of the use of conventional 304 or 316 stainless steel material, when the conveying medium is easy to react with stainless steel materials (such as: When nitric acid, hydrochloric acid, etc.), the service life of the traditional IH stainless steel chemical centrifugal pump will be greatly reduced, so it is imperative to develop the chemical pump that can adapt to the special working conditions.

ISW horizontal pipeline centrifugal pump IS simplified on the basis of IS series coupling type centrifugal pump, compared with IS centrifugal pump, ISW horizontal centrifugal pump installation area reduced by 30%.

Customers who have used the pump know that the mechanical seal of the pump as a vulnerable part of the pump, when the conveying medium is special or not used when it is easy to damage, then there is no mechanical seal that can take into account these two points, not so easy to break, the answer is yes.

Stainless steel centrifugal pump Guangdong Dongguan where to sell, Atach brand strong and durable

Now all over Guangdong are enveloped in the voice of environmental protection, environmental protection benefits the country and the people, it is worth advocating. Since the environmental protection is strictly grasped, how to choose the transmission pump necessary for environmental protection work - stainless steel centrifugal pump has become a problem often considered by major environmental protection companies. After the experience analysis of Atach pump company, environmental protection companies often deal with filtrate containing particulate matter, containing corrosion and containing temperature, for corrosion resistance, wear resistance and high temperature, what pump can all meet the working conditions and the cost of civilianization? Atach Pumps' new stainless steel centrifugal pump -ATH type (old model called IH) cantilever stainless steel centrifugal pump is the first. Gene

Are you still using the old IH chemical pump? Try the new 10th generation IH chemical pump from Atach



A variety of stainless steel material options, stainless steel 304, 304L, 316, 316L, 321 and titanium material options;

;Sealing forms are: single end mounted mechanical seal, single end mounted mechanical seal, double end mechanical seal (wear-resistant with water cooling device, suitable for high temperature media containing particle impurities), packaged mechanical seal (the latest results), Guangdong Atach pump industry, all the pumps inside there is always a suitable for you.

Customized steel lined fluorine plastic magnetic pump according to customer special requirements, shipped to Indonesia

The customer's conveying medium is CRO3 solution, which needs to be started continuously for 24 hours, 4 sets of small order test orders, steel lined fluorine plastic material Guangdong magnetic pump, Aitke is trustworthy.

Stainless steel corrosion resistant centrifugal pump new cast impeller batch

Guangdong pump Factory today arrived a batch of new impellers, stainless steel and copper material two kinds, are precision casting, corrosion and wear resistance, all impellers have undergone strict dynamic balance test to ensure the smooth and efficient operation of each stainless steel centrifugal pump.

The new mold has finally been trial-produced, and the new generation of stainless steel chemical pump pump shell has been released, adding new blood to the Guangdong pump factory.

The pump shell is made of stainless steel precision casting, to undertake stainless steel 304, stainless steel 304L, stainless steel 316, stainless steel 316L, stainless steel 321, titanium alloy, welcome customers to consult.

IHF series fluoroplastic centrifugal pump pump body and suspension semi-finished products